VeEX VePAL TX300 User Manual Download Page 333

Page: 333 / 421

Summary:

The Summary tab displays the status of each service and test as Pass, Failed, Pending, or Disabled.

Perf. Test - Service 1

Performance Test

The

Service #

tabs display min, mean, and max values for

IR Mbps

FTD

FDV

Frame Loss Count

Frame Loss Ratio (%)

Availability

, and

Errored Frame Count

. Pass/Fail/Pending status of each test is displayed on the top of each table.

IR Mbps

FTD

FDV

Frame Loss Count

Frame Loss Ratio (%)

definitions are listed in the

Configuration Test

section.

Availability:

Minimum percentage of service availability allowed to still be compliant with the SLA. The service becomes

unavailable if more than 50% of the frames are errored or missing in a one second interval. Availability is only guaranteed

for traffic conforming to the CIR.

Total RX Frames:

Total number of frames received

Errored Frame Count:

Number of frames with CRC or IP Checksum errors

Measured values that do not meet the service test parameters set in the Bandwidth and Threshold tabs cause the test to fail.

The

Summary

tab displays the status of each service and test as

Pass

Failed

Pending

, or

Disabled

Perf. Tests - Summary

TX300/e_e-manual_D07-00-033P_RevG00

Summary of Contents for VePAL TX300






































































































































































































































































































































































































































Search results

Summary of Contents for VePAL TX300

Reviews:

Related manuals for VePAL TX300

Brands by name

Popular brands

VeEX VePAL TX300, User Manual

Search results

Summary of Contents for VePAL TX300

Reviews:

Related manuals for VePAL TX300

Brands by name

Popular brands