VeEX VePAL TX300 User Manual Download Page 214

Page: 214 / 421

11.5 Round Trip Delay

Tap the Round Trip Delay in the PDH Tools screen to perform a round trip delay measurement.

The Round Trip Delay (Propagation Delay) measurement works by sending a test pattern with an error. The time it takes for the

error to reach the receiver is the propagation time through the network.

Setup:

View the Round Trip Delay of a looped back signal

Set check box on Setup RX pattern to Out-of-Service

RTD Results

Go back to top

Go back to TOC

11.6 E1 RX Data

The PDH E1 RX data shows received data and captures the current timeslots.

TX300/e_e-manual_D07-00-033P_RevG00

Summary of Contents for VePAL TX300






































































































































































































































































































































































































































Search results

Summary of Contents for VePAL TX300

Reviews:

Brands by name

Popular brands

VeEX VePAL TX300, User Manual

Search results

Summary of Contents for VePAL TX300

Reviews:

Brands by name

Popular brands