manualshive.com logo in svg

VeEX VePAL TX300, User Manual

Share
Download
VeEX VePAL TX300 User Manual Download Page 148

Go back to top

 

Go back to TOC

9.4 Trace Identifier (Trail Trace Identifier)

Tap the Trace Identifier icon to display the screen shown below. There are tabs for Tx and RX settings of the TTI.

Trace Identifier (Trail Trace Identifier)

Trail Trace Identifier

TTI similar to the J0 byte in SONET/SDH, is used to identify the signal from the source to the

destination within the network. The TTI contains the so called Access Point Identifiers (API) which

are used to specify the Source Access Point Identifier (SAPI) and Destination Access Point Identifier

(DAPI). The APIs contain information regarding the country of origin, network operator and

administrative details.

TX300/e_e-manual_D07-00-033P_RevG00

Summary of Contents for VePAL TX300






































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands