manualshive.com logo in svg

VeEX UX400, User Manual

Share
Download
VeEX UX400 User Manual Download Page 80

Go back to top

 

Go back to TOC

6.4.1.2 Service Attributes

Bandwidth Profile Parameters

The Bandwidth Profile specifies how much traffic the customer is authorized to transmit and how the frames are prioritized within the network. In the Bandwidth table, the

user specifies the following bandwidth criteria:

CIR:

 Committed Information Rate. This is the guaranteed maximum rate at which the customer can send frames that are assured to be forwarded through the

network without being dropped. Tap on the box to enter a rate and choose between 

IR Mbps

, 

IR Gbps

,

 ULR Mbps 

or

 ULR Gbps

. Allowed values range from

0.01Mbps to the line bandwidth.

Information Rate (IR):

 Measures the average Ethernet frame rate starting at the MAC address field and ending at the CRC.

Utilized Line Rate (ULR):

 Measures the average Ethernet frame rate starting with the overhead and ending at the CRC.

V-SAM Services - Header

Excess Information Rate (EIR):

 Maximum rate above the CIR at which the customer can send frames that will be forwarded on a best effort basis, but may be

dropped in the event of congestion within the network. The combined CIR and EIR must not exceed the line bandwidth. Traffic beyond CIR + EIR will be dropped

when it enters the carrier's network. Tap on the box to enter a rate. EIR is expressed in terms 

IR Mbps

, 

IR Gbps

,

 ULR Mbps 

or

 ULR Gbps

. Select a term to

express EIR or select 

Disable

 to disable the test.

Traf. Policing:

 Enable or Disable the traffic policing test. For this test, traffic is transmitted at 25% higher than the CIR+EIR. The Policing test fails if the higher

traffic rate is allowed through the network.

Color Aware Service:

 Enable or Disable 

Note:

 A VLAN Tag must be enabled for Color Aware Service to be enabled.

CBS

 and 

EBS 

are currently not supported with this release.

V-SAM Setup - Services - Service Attributes

UX400 10G e-Manual D07-00-058P RevA00

Page 80 of 209

Summary of Contents for UX400


















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands