VeEX UX400 User Manual Download Page 78 | Manualshive

Page: 78 / 209

VeEX UX400 User Manual Download Page 78

Phase 2: Service Performance Test

Services running on the same line are tested simultaneously over an extended period of time, to verify network robustness. Service Acceptance Criteria (SAC) including

Frame Transfer Delay (FTD), Frame Delay Variation (FDV), Frame Loss Ratio (FLR) and Availability (AVAIL) are verified for each service.

6.4.1 V-SAM Setup

General (Page 1 and 2)

V-SAM Profile:

Delete, Save, Save as..., Default, or Last Configuration.

# of Services:

Select the number of services to run. Up to 10 services can be chosen for the 10 GE interface.

Display:

IR or ULR

Service Configuration Test:

Enable or Disable the configuration test.

Service Performance Test:

Enable or Disable the performance test.

Service Configuration

and

Performance Tests

can be enabled independently.

CIR Test Config:

Tap on the box to configure the Committed Information Rate Test on another screen.

Duration:

Select the

Service Performance Test

duration. Options are 15min, 30min, 1hr, 2hr, 24hr or user defined. If user-defined is selected, input a duration

between 1-10000 min.

Enabling/Disabling Tests

A check next to the Service number in the Service Summary table indicates that the test for the

corresponding service is set to run. Tap on the box to remove the check and cancel the test for that

service.

V-SAM - Setup - General (Page 1)

V-SAM - Setup - General (Page 2)

UX400 10G e-Manual D07-00-058P RevA00

Page 78 of 209

«
...
76
77
78
79
80
...
»

Summary of Contents for UX400


















































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands