VeEX UX400 User Manual Download Page 64 | Manualshive

Page: 64 / 209

background image

6.3.1.3 Threshold Settings

Threshold settings can be enabled or disabled for the throughput and latency tests.

When enabled, threshold settings can be configured for all of the test frames selected in the frame settings tab.

A Pass/Fail criteria will be applied when the threshold settings are enabled. For example, if the throughput threshold value for a 64 byte frame is configured for 80%, then a

Pass criteria is assigned if the throughput rate is 80% or better.

The threshold values for Throughput and Latency can be customized per user requirements. Tap on the selected value to edit.

RFC2544 Thresholds Setup

6.3.1.4 Throughput, Latency, Frame Loss, and Burst Settings

The RFC 2544 test suite allows the user to run all four tests, one of the four tests, or a combination of any of the four tests. The user simply has to enable/disable which

tests to perform by checking/unchecking a selection box in the respective tab for each test. By default all four tests are enabled. Throughput test can not be disabled.

The following parameters must be configured before running the RFC 2544 conformance test suite.

Throughput

:

Max Rate:

Up to 100% of the negotiated line rate. The default value is 100%.

This is the maximum transmit rate to perform the throughput test for each test frame size.

This rate may be configured as a % of the total line rate or in Mbps. For example the Max Rate is configured to be 90% and the negotiated line rate of the

link is 100Mbps, then the maximum transmit rate will be 90Mbps or 90% of the line rate.

Resolution:

Input any value between 0.001% and 1%. The default value is 1%. Resolution refers to the resolution in searching for the throughput rate. If 1% is

selected, the throughput rate will be searched with ±1% accuracy.

Duration:

5 to 999 seconds. The default value is 20 seconds.

The duration is the amount of time the throughput test is run for, for each frame size at a given rate.

RFC2544 Throughput Settings

UX400 10G e-Manual D07-00-058P RevA00

Page 64 of 209

«
...
62
63
64
65
66
...
»

Summary of Contents for UX400


















































































































































































































Reviews:

No comments

Related manuals for UX400

Brand: E-fly Pages: 16

Brand: Lawler Pages: 6

Brand: Data Aire Pages: 28

Brand: Parker Pages: 44

Brand: National Instruments Pages: 102

Brand: NAU ROBOTICS Pages: 109

Maschine Mikro MK2

Brand: Native Instruments Pages: 181

Brand: OBSIDIAN CONTROL SYSTEMS Pages: 13

SHERPA MONOBLOC B0812

Brand: Olimpia splendid Pages: 44

Brand: Olimpia splendid Pages: 44

Brand: Olimpia splendid Pages: 16

Brand: X Rocker Pages: 38

IntelliZone2 MasterStat

Brand: Water Furnace Pages: 44

CEmarking RCX221

Brand: Yamaha Pages: 468

Brand: M-system Pages: 10

Brand: Linear Technology Pages: 7

J1000 CIMR-JC series

Brand: YASKAWA Pages: 25

Brand: Fancom Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands