VeEX UX400 User Manual Download Page 48

Page: 48 / 209

Error Injection

After pressing

Start

, error injection can be enabled by pressing the

Error Inj.

button on the right

side of the screen.

Go back to top

Go back to TOC

6.2.1.4 Alarm Injection Settings

Alarm injection can be performed during a test. The type of alarms and alarm injection are configured in the Alarm Injection tab. Once the test is running, alarm injection can

be performed by pressing the

Alarm Inject

button on the right side of the screen.

Alarm Type:

Local Fault, Remote Fault, PCS-HI-BER, PCS-LOBL

Alarm Flow:

The alarm flow determines how the selected alarms will be injected. A specific Count or Conitnue (continuous) can be selected.

Alarm Length:

1s, 10s, or 100s.

BERT Setup - Alarm Injection

Go back to top

Go back to TOC

6.2.1.5 Starting/Stopping a BERT

UX400 10G e-Manual D07-00-058P RevA00

Page 48 of 209

Summary of Contents for UX400


















































































































































































































Search results

Summary of Contents for UX400

Reviews:

Related manuals for UX400

Brands by name

Popular brands

VeEX UX400, User Manual

Search results

Summary of Contents for UX400

Reviews:

Related manuals for UX400

Brands by name

Popular brands