manualshive.com logo in svg

VeEX UX400, User Manual

Share
Download
VeEX UX400 User Manual Download Page 102

6.6 Loopback

The Loopback application in the main menu allows the user to establish a manual loopback on the test set. The loopback function is used when an end-to-end test needs

to be performed with one of the test partners in software loopback mode. The loopback function will loopback the incoming traffic to the test set back into the network

under test.

The type of traffic that the loopback function loops back will depend on the type of test layer configured (Layer 1, 2, 3, or 4). Additional criteria can be set to allow only

messages with specific criteria to be looped back. To specify loopback parameters, select the desired parameter and choose 

Enable 

from the drop-down menu. Tap on the

box and input a value or select one of the drop-down menu choices:

Layer 1

: All incoming traffic to the Rx loopback interface will be sent out unaltered to the Tx loopback interface.

Layer 2, 3, & 4

: In a Layer 2 or 3 loopback all incoming test traffic will be looped back.

The loopback function will swap the MAC destination and MAC Source addresses (for Layer 2) or MAC and IP destination and source addresses (for Layer 3).

All incoming frames with CRC errors will be dropped, similar to what an Ethernet switch does.

All broadcast and multicast frames will be dropped including any incoming unicast frames that have the MAC Source address equal to the MAC Destination

address.

6.6.1 Setup

Loopback Parameters

: The following parameters are available on Layer 2, 3 and 4. For more information on the parameters, please see 

6.2.1.1 BERT Header Settings

 in

the BERT section. It is possible to enable any of these parameters to create a customer loopback filter. For example, enabling a filter with VLAN 64, Priority 7, will only loop

back traffic corresponding to these values.

VLAN ID

VLAN Priority

MAC Source

MAC Destination

IP Source Address (Layer 3 & 4 only)

IP Destination (Layer 3 & 4 only)

Precedence (Layer 3 & 4 only)

TOS Value (Layer 3 & 4 only)

UDP SPort (Layer 4 only)

UDP DPort (Layer 4 only)

Loopback Setup Layer 2

Loopback Setup Layer 3

 

Loopback Setup Layer 4

UX400 10G e-Manual D07-00-058P RevA00

Page 102 of 209

Summary of Contents for UX400


















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands