VeEX MTX150x Lite User Manual Download Page 98

Page: 98 / 148

Platform Functions

Gateway:

PASS indicates that the gateway IP address is valid.

DNS:

PASS indicates that the DNS IP address is valid.

Ping

The Ping Result provides the number of Sent, Received, Unreach, Missing, and the Round Trip delay.

Ping Testing

Ping is a popular computer network tool used to test whether a particular host is reachable across an IP net-
work. A ping is performed by sending an echo request or ICMP (Internet Control Message Protocol) to the echo
response replies.

Ping Setup

Profile:

Delete, Save, Save as..., or Default.

Destination:

Press the drop -down menu and enter the destination IP address or URL to ping.

Number of Pings:

Enter the number of ping attempts (up to 10000) that will be performed to reach

the network device.

If Continuous Ping is selected, the user is not required to enter the number of pings. The test

set will continuously ping the target host until the user presses

Stop

Length:

Enter the length of the ICMP echo request packet transmitted.

Ping/Sec:

Enter the Ping repetition rate (Ping/second).

Summary of Contents for MTX150x Lite














































































































































Search results

Summary of Contents for MTX150x Lite

Reviews:

Related manuals for MTX150x Lite

Brands by name

Popular brands

VeEX MTX150x Lite, User Manual

Search results

Summary of Contents for MTX150x Lite

Reviews:

Related manuals for MTX150x Lite

Brands by name

Popular brands