VeEX MTX150x Lite User Manual Download Page 39

Page: 39 / 148

Ethernet

Ping Setup

Ping Setup

Profile:

Delete, Save, Save as..., or Default.

Destination:

Press the drop -down menu and enter the destination IP address or URL to ping.

Number of Pings:

Enter the number of ping attempts (up to 10000)

that will be performed to reach the network device.

If Continuous Ping is selected, the user is not required to enter the number of pings. The test

set will continuously ping the target host until the user presses

Stop

Length:

Enter the length of the ICMP echo request packet transmitted.

Ping/Sec:

Enter the Ping repetition rate (Ping/second).

Time Out:

Time-to-Live (TTL) in milliseconds. Enter the maximum time allowed (in ms, up to 99999

ms) between an ICMP ping and echo response.

Once the parameters are configured, press

Start

to begin the test.

Ping Results

Pressing Ping will take you to the Result tab and start the Ping test.

Summary of Contents for MTX150x Lite














































































































































Search results

Summary of Contents for MTX150x Lite

Reviews:

Related manuals for MTX150x Lite

Brands by name

Popular brands

VeEX MTX150x Lite, User Manual

Search results

Summary of Contents for MTX150x Lite

Reviews:

Related manuals for MTX150x Lite

Brands by name

Popular brands