VeEX MTX150x Lite User Manual Download Page 34

Page: 34 / 148

Ethernet

DNS:

Selecting Manual DNS opens another menu. Select from Off, Primary, or Primary & Sec-

ondary. Enter the Primary and/or Secondary DNS if required.

IP Setup - IPv4

IPv4 or IPV6

IP Type:

IPv4 or IPv6

IP Address:

Static, DHCP (IPv4 only) or AUTO (IPv6 only)

Static:

The user is required to enter a Local IP, Gateway address, and Subnet. All Static fields can

be filled by tapping on the section to access an alphanumeric keyboard

Local IP:

IPv4/IPv6 address of the test set

Gateway:

IPv4/IPv6 address of the network gateway

DNS:

Input a primary and secondary DNS

CIDR

(IPv6 only)

The user can enter a Classless Inter -domain Routing Network

Subnet

(IPv4 only)

The user can enter a subnet mask

Gateway and DNS:

Enable/Disable. Enables entering the Gateway and DNS.

Summary of Contents for MTX150x Lite














































































































































Search results

Summary of Contents for MTX150x Lite

Reviews:

Related manuals for MTX150x Lite

Brands by name

Popular brands

VeEX MTX150x Lite, User Manual

Search results

Summary of Contents for MTX150x Lite

Reviews:

Related manuals for MTX150x Lite

Brands by name

Popular brands