manualshive.com logo in svg

Veeder-Root TLS-450, Setup And Operation

Share
Download
Veeder-Root TLS-450 Setup And Operation Download Page 71

TLS-450 Setup and Operation Screens Manual 

 

60 

 

Device Setup - Line Pressure Sensor 

 

 
This screen allows you to setup Pressurized Line Leak Detection (PLLD) pressure sensors that have 
been connected to the console.    

Configured  

Allowable selections: Enabled, Disabled 
Default: Disabled 

Address 

Allowable selections: Choose from drop-down list of available Line Pressure sensors, Not Assigned 
Default: Not Assigned 

Label 

Allowable selections: Up to 20 alphanumeric characters 
Default: Blank 

Serial Number 

This is a read-only value. 
 
 
 
 

Summary of Contents for TLS-450

























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands