Home
/
Veeder-Root
/
TLS-450
/
Setup And Operation

Veeder-Root TLS-450, Setup And Operation

Share

Page: 356 / 408

Veeder-Root TLS-450 Setup And Operation Download Page 356

TLS-450 Setup and Operation Screens Manual

345

Install Screen Fields

Status Bar

Displays the current operation in progress. Possible messages include:

•

Idle

•

Scanning Devices

•

Reading Update List

•

Waiting Selection

•

Downloading

Feature

This column contains a list of features which are available to be installed. Multiple features may be
installed concurrently. Touch the boxes beside each of the desired items in this column. If you change
your mind about a selection, touch the box again to remove the check.

Status

The current status of each feature is also displayed with one of the following messages:

•

Ready to Install

•

Installation in Progress

Control Button (Right Side of Screen)

Install

Touch to install a selected (checked) feature. This button is inactive until at least one entry has been
selected.

«
...
354
355
356
357
358
...
»

Summary of Contents for TLS-450

























































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands