manualshive.com logo in svg

Veeder-Root TLS-450, Setup And Operation

Share
Download
Veeder-Root TLS-450 Setup And Operation Download Page 355

TLS-450 Setup and Operation Screens Manual 

 

344 

 

Software Maintenance - Install 

 

 
The Install tab screen is use to control the installation of downloaded software. During the installation 
process, several dialog boxes will be displayed to inform you of key events. 
 
During Installation there must be no dispensing. However, the installation process only takes a few 
minutes. Following installation, the console converts the setup databases. If new features are installed 
and activated, setup(s) relevant to the new feature(s) will be required. 

Installation Procedure 

1.  Touch the features on the list you want to install and then touch the Install button on the right side 

of the screen. 

2.  Touch the OK button on the System Restart dialog box, or touch Cancel to abort the installation 

or to reselect the feature(s) you want to install. The console will restart with the newly installed 
features. 

3.  If you used the USB port of the Ethernet/USB module to install the new features, remove the USB 

Adapter and put it in a safe place. Perform setup for the newly installed features. 

4.  If you used the CPU board printer's USB port to install the new features, turn off power to the 

console.  Open the left door of the console and remove the USB Adapter from the printer port and 
reconnect the Printer cable. Close the left door and replace the two #8 taptite screws. Turn on 
power to the console and perform setup for the newly installed features. 

Summary of Contents for TLS-450

























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands