manualshive.com logo in svg

Veeder-Root TLS-450, Setup And Operation

Share
Download
Veeder-Root TLS-450 Setup And Operation Download Page 348

TLS-450 Setup and Operation Screens Manual 

 

337 

 

Software Maintenance 

Connecting USB Thumb Drive for Software Maintenance 

Procedures 

Follow the steps below to connect a valid V-R Code/Features USB thumb drive or a V-R Recovery USB 
thumb drive to the TLS-450 console prior to performing Software Maintenance procedures. 
 

1.  Get the USB Adapter and upgrade i-button from the upgrade kit. Remove the plastic end cap 

from the USB Adapter and Insert the i-button in the adapter as shown in the diagram below: 

 

 

 

2.  Replace the plastic retaining cap on the adapter after inserting the i-Button. 

  

3.  Plug the USB Adapter into the USB port of the console's Ethernet/USB card and follow the 

required Software Maintenance procedures. When you have completed the Software 
Maintenance procedure(s) remove the thumbdrive. 
 
If the console does not have an Ethernet/USB card, continue to step 4. 
  

4.  Turn off power to the console. 
5.  Using a T-15 Torx driver, remove the two #8 taptite screws the left door of the console (see 

below): 
 

Summary of Contents for TLS-450

























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands