manualshive.com logo in svg

Veeder-Root TLS-450, Setup And Operation, Page: 192 / 408

Share
Download
Veeder-Root TLS-450 Setup And Operation Download Page 192

TLS-450 Setup and Operation Screens Manual 

 

181 

 

Printer Setup - Setup 

Printer Setup Screen 1 

 

 
This screen can configure printers connected locally to the USB port, or connected remotely through a 
communications network. You can also display printer status, and show jobs in printer queues. 
 
Use the Get Printers button to locate available printers, or enter a URI (Uniform Resource Identifier) field, 
as described below.  
 
First select a PRINTER button on the bottom of the screen: PRINTER 2 through PRINTER 5. 
 
Note: The Integral printer TLSIntegralPrinter occupies PRINTER 1. This device is installed in the left door 
of the console. 
 

 

Summary of Contents for TLS-450

























































































































































































































































































































































































































Reviews:

No comments