manualshive.com logo in svg

Veeder-Root TLS-450, Setup And Operation

Share
Download
Veeder-Root TLS-450 Setup And Operation Download Page 171

TLS-450 Setup and Operation Screens Manual 

 

160 

 

Add/Edit Contact Entry - TCP/IP 

 

 
The Add Contact Entry - TCP/IP screen lets you add/edit communication parameters for TCP/IP outbound 
connectivity for the current contact. 
 
This connection method is available if an Ethernet Comm Device is installed in the console. 

Remote TCP/IP Address 

Enter the remote host's TCP/IP address. 
 
Allowable selection: IP Address Formatted XXX.XXX.XXX.XXX, where XXX is 0 to 255, OR also a server 
address such as 'myServer.bigg.com'. 
Default selection: 0.0.0.0  

Remote TCP/IP Port  

Enter the remote host's TCP/IP port. 
 
Allowable selection: 0 to 65535   
Default selection: 20001 

 

Local TCP/IP 

Enter the local TCP/IP assignment for the current contact. 

Summary of Contents for TLS-450

























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands