background image

  

Introduction

Safety Warnings

2

Safety Warnings

Related Documents

DOCUMENTS REQUIRED TO INSTALL EQUIPMENT

This equipment must be installed according to the applicable installation document:

REFERENCE MANUALS

577014-073

TLS-450PLUS Console Site Prep And Installation Manual

WARNING

This console contains high voltages which can be lethal. It is also connected to low 
power devices that must be kept intrinsically safe.

FAILURE TO COMPLY WITH THE FOLLOWING WARNINGS AND SAFETY 
PRECAUTIONS COULD CAUSE DAMAGE TO PROPERTY, ENVIRONMENT, 
RESULTING IN SERIOUS INJURY OR DEATH.

1. Turn off and tag power at the circuit breaker. Do not connect the console AC 

power supply wires at the breaker until all devices are connected.

2. Attach conduit from the power panel to the console's Power Area knockouts 

only.

3. Comply with all applicable codes including: the National Electrical Code; 

federal, state, and local codes; and other applicable safety codes.

Connecting power wires to a live circuit can cause electrical shock that may result in 
serious injury or death. 

Routing conduit for power wires into the intrinsically safe compartment can result in 
fire or explosion resulting in serious injury or death.

Equipment

ATEX

Descriptive System

IECEx

Descriptive System

UL/cUL 

Control Drawing

Document No.

Document No.

Document No.

Associated Apparatus

TLS-450PLUS

331940-006

331940-106

331940-008

Intrinsically Safe Apparatus for Wireless Applications

Tank Gauge Accessories

331940-005

331940-105

331940-012

OFF

Summary of Contents for TLS-350l















Reviews: