Veeco Dimension 3100 Manual Download | Manualshive

Page: 264 / 376

background image

Force Imaging

Force Modulation with ‘Negative LiftMode’

244

Dimension 3100 Manual

Rev. D

13.7.2 Obtain a TappingMode Image

While negative LiftMode force modulation data is imaged using

Channel 2

, height data is obtained

using TappingMode on

Channel 1

. You must obtain a satisfactory TappingMode image to generate

good data.

1. Verify that the

Interleave mode

parameter on the

Interleave Controls

panel is

Disabled

.

2. Verify that the

AFM mode

parameter in the

Other Controls

panel is set to

Tapping

.

3. Select

Realtime

>

View

>

Sweep

>

Cantilever

or the

Cantilever Tune

icon.

Enter a

main controls

Start frequency

value of

5kHz

and

End frequency

value of

100kHz

for

FESP tips.

4. Set

Target Amplitude

to

1

-

2V

, and click the

Auto Tune

button, or tune manually.

5. Click the

Interleave

Controls

button to verify that the bimorph drive parameters are correct.

6. Exit the

Cantilever Tune

dialog box.

7. Verify that all

Scan controls

and

Feedback Controls

parameters are set for obtaining a

TappingMode image.

8. Set the

Channel 1

panel

Data type

parameter to

Height

.

9. Set the

Line direction

to

Retrace

and enter an appropriate

Data Scale

value for your

sample.

10. Engage the tip on the surface and obtain a good TappingMode image.

13.7.3 Obtain a Negative LiftMode Force Modulation Image

1. Set the

Data type

parameter in the

Channel 2

panel to

Amplitude

. Set the

Line direction

parameter to

Retrace

.

2. Switch the

Interleave mode

parameter in the

Interleave Controls

panel to

Lift

. Negative

LiftMode imaging is now in effect.

3. Using the left arrow key, optimize the negative LiftMode image by slowly decreasing the

Lift scan height

parameter in the

Interleave Controls

panel from zero until you reach the

surface. In most cases, you should not go below -

60.0nm

.

Note:

This is sometimes best performed while in

Realtime

>

View

>

Scope

Mode

.When the interleaved scan is enabled, the tip’s TappingMode height

above the sample reduces by the

Lift scan height

amount. This places the

oscillating tip in contact with the sample as surface features are proﬁled. The
contrast between light and dark reveals areas of high and low elasticity, with the
dark area indicating harder material and the lighter areas indicating softer
material.

«
...
262
263
264
265
266
...
»

Summary of Contents for Dimension 3100

























































































































































































































































































































































































Reviews:

No comments

Related manuals for Dimension 3100

Brand: Elenco Electronics Pages: 2

300 LED 1013366

Brand: 3B SCIENTIFIC PHYSICS Pages: 12

Brand: Bresser Junior Pages: 60

Brand: MshOt Pages: 15

Brand: BMS Pages: 7

Brand: Levenhuk Pages: 48

Brand: 3B SCIENTIFIC PHYSICS Pages: 24

Brand: Bresser Pages: 44

Brand: Levenhuk Pages: 46

Brand: Olympus Pages: 46

Brand: VWR Pages: 32

VisiScope BL103 POL

Brand: VWR Pages: 72

Brand: Dino-Lite Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands