Vecow ECX-2300 PEG User Manual Download

Page: 19 / 144

©Vecow ECX-2600/2400/2300 PEG User Manual

GENERAL INTRODUCTION

1.3.5

Specifications of ECX-2300 PEG

System

Processor

Intel

10th Generation Xeon

/Core™ i9/i7/i5/i3 Processor

(Comet Lake-S)

Chipset

Intel

W480E

BIOS

AMI

SIO

IT8786E

Memory

• DDR4 2933MHz (ECC/Non-ECC)

• Up to 64GB

• 2 260-pin SO-DIMM Socket

I/O Interface

Serial

4 COM RS-232/422/485 (ESD 8kV)

USB

6 USB 3.2 (External)

Isolated DIO

16 GPIO

LED

Power, HDD, Wireless

SIM Card

3 Nano SIM Card Socket (External)

Expansion

Mini PCIe

2 Full-size Mini PCIe Socket for PCIe/USB/External SIM

Card/mSATA

PCI/PCIe

• 1 PCIe x16 Slot

• 1 PCIe x4 Slot

M.2

• 1 M.2 Key B Socket (3042/3052)

• 1 M.2 Key E Socket (2230)

Graphics

Graphics Processor

• Intel

UHD Graphics 630

• Independent Graphics : By request

Interface

Up to 7 independent displays :

• 1 VGA : Up to 1920 x 1080 @60Hz

• 1 DVI-D : Up to 1920 x 1080 @60Hz

• 2 DisplayPort : Up to 4096 x 2304 @60Hz

• By requested graphic card

Storage

SATA

4 SATA III (6Gbps) support S/W RAID 0, 1, 5, 10

mSATA

2 SATA III (Mini PCIe Type, 6Gbps)

M.2

1 M.2 Key M Socket (2280, PCIe x2)

Storage Device

• 1 Micro SD Card, Push-in/Push-out Ejector

• 4 Front-access 2.5" SSD/HDD Tray

Audio

Audio Codec

Realtek ALC888S-VD, 7.1 Channel HD Audio

Audio Interface

1 Mic-in, 1 Line-out

Ethernet

LAN 1

Intel

I219LM GigE LAN supports iAMT 14.0

LAN 2

Intel

I210 GigE LAN

Summary of Contents for ECX-2300 PEG

















































































































































Search results

Summary of Contents for ECX-2300 PEG

Reviews:

Related manuals for ECX-2300 PEG

Brands by name

Popular brands

Vecow ECX-2300 PEG, User Manual

Search results

Summary of Contents for ECX-2300 PEG

Reviews:

Related manuals for ECX-2300 PEG

Brands by name

Popular brands