background image

 

 

1.  Safety instructions 

  This Device is suitable for indoor use only. 

  All modifications will void the warranty. 

  Repairs have to be carried out by skilled personnel only. 

  Only use fuses of the same type and original parts as spare parts. 

  Protect the Unit from rain and humidity to avoid fire and electric shocks. 

  Make sure to unplug the power supply before opening the housing. 

1.1. 

Instructions for a safe and efficient operation

 

Be careful with heat and extreme temperature 

Only use the device in a place where no extreme temperatures will occur. 
Do not keep it in a temperature bellow 32°F /0°C, or exceeding 104°F /40°C. 
Avoid exposing it to direct rays of the sun or near a heating appliance. 
 

Keep away from humidity, water and dust 

Do not place the set in a location with high humidity or lots of dust.  
Containers with liquid should not be placed on the set. 
 

Avoid placing it on un-stable location 

Select a level and stable location to avoid vibration. 
 

Do not use chemicals or volatile liquids for cleaning 

Use a clean dry cloth to wipe off the dust. Metall Parts can be cleaned with a wet soft cloth for 
stubborn dirt. 
 

If out of work, contact sales agency soon 

If any troubles occurs, remove the power plug immediately, and contact with an engineer for repairing, 
do not open the cabinet by yourself, it might result a danger of electric shock. 
 

Take care with the power cable 

Never pull the power cable to remove the plug from the receptacle, be sure to hold the plug. When not 
using the device for an extended period of time, be sure to disconnect the plug from the receptacle. 
 

IMPORTANT: 

Damages caused by the disregard of this user manual are not subject to warranty. The dealer will not 
accept liability for any resulting defects or problems. Make sure the electrical connection is carried out 
by qualified personnel. All electrical and mechanical connections have to be carried out according to 
the European safety standards. 

 

 

3 / 16 

Summary of Contents for Strobe Xenon 3000DMX

















Reviews: