background image

 

POW67904 

EN

 

Copyright © 2014 VARO NV 

P a g e

 | 

3

 

www.varo.com 

5  BEFORE START-UP, NOTE THE FOLLOWING! 

 

The pump can be connected to any shock-proof plug which has been installed according 
to regulations. The plug must have a supply voltage of 230 V ~ 50 Hz. Fuse min. 6 Amp. 

Caution!  

When  the  pump  is  to  be  used  near  swimming  pools  or  garden  ponds  and  in  their  area  of 
protection, it must be equipped with a PRCD (residual current circuit breaker) with a nominal 
trip current of max. 30 mA (according to VDE 0100, part 702 and 738). The pump must not be 
operated while people are in the  swimming pool or in the garden pond!  Please contact your 
electrician! 

Attention! 

(Important  for  your  own  security)  Before  starting  to  run  your  new  submersible  pump,  please 
have the following items checked by an expert: 

 

Ground connection 

 

Zero conductor 

 

Fault current breaker switch must correspond the safety regulations of the power plants 
and they must work faultlessly. 

 

The electrical connections must be protected from moisture. 

 

If there is danger of flooding, the electrical connections must be taken to higher ground. 

 

Circulation of aggressive fluids, as well as the circulation of abrasive materials must be 
avoided at all costs. 

 

The submersible motor-driven pump must be protected from frost. 

 

The pump must be protected from running dry. 

 

Access on the part of children should also be prevented with appropriate measures. 

Consistency 

Your submersible pump is designed for the circulation of water with a  maximum temperature 
of  35°  C.  This  pump may  not  be used for  other fluids,  especially motor  fuels,  cleaning fluids, 
and other chemical products! 

6  INSTALLATION 

The submersible pump is installed as follows: 

 

In a stationary position with fixed pipeline 

or 

 

in a stationary position with a flexible hose pipe. 

Please note! 

You  should  never  install  the  pump  by  suspending  it  unsupported  from  its  delivery  pipe  or 
power cable. The submersible pump must be suspended from the specially provided handle or 
be placed on the bottom of the shaft. To guarantee that the pump works properly, the bottom 
of the shaft must be kept free of sludge and dirt of all kinds. 
If the level of water sinks too far, any sludge in the shaft will dry out quickly and stop the pump 
from starting up. ,Therefore it is necessary to check the submersible motor pump regularly (by 
carrying out start-up tests). The floater is adjusted in a way that the pump can immediately be 
started 

Note! 

The  pump  shaft  should  have  minimum  dimensions  of  40  x  40  x  50  cm,  so  that  the  floating 
switch can move freely. 

Mains supply 

Your new submersible pump is equipped with a shock-proof plug according to regulations. The 
pump  is  designed  to  be  connected  to  a  230V  -  50  Hz  earthed  socket.  Make  sure  that  the 
socket  is  sufficiently  secured  (min.  6  Amp.)  and  is  in  excellent  condition.  Introduce  the  plug 
into the socket and the pump is ready to go. 

Summary of Contents for POWERplus Water POW67904









Reviews: