background image

 

POWEG8012 

EN

 

Copyright © 2021 VARO 

P a g e

 | 

9

 

www.varo.com 

 

Do not use the unit for the cutting of shrubs, brushwood or underwood. 

 

Regularly check the metal cutting blade's condition and change damaged cutting blades. 

10 CLEANING AND MAINTENANCE 

ATTENTION!  Let  any  repair  and  maintenance  work  not  described  in  these 
instructions  be  carried  out  by  a  professional  service  shop.  Only  use 
original  replacement  parts.  Any  maintenance  and  cleaning  tasks  should 
only  be  carried  out  when  the  motor  is  switched  off  and  the  ignition 
disconnected. Risk of injury! Let the machine cool down before undertaking 
any  maintenance  or  cleaning  tasks.  Parts  of  the  motor  are  hot.  There  is  a 
risk of getting burned! 

 

This tool corresponds to the relevant safety provisions. 

 

Repairs, service and maintenance must be carried out exclusively by authorized service 
workshops/trained professionals. 

 

Only original spare parts may be used for repairs; otherwise there is a risk of injury for the 
operator. 

10.1 

Unit cleaning 

Subject your unit to regular cleaning and care. It will deliver good performance for a very long 
time. 

 

After every operation clean the cutting attachment of grass and soil. 

 

Clean the unit with a soft brush or a rug. 

 

The unit must not be sprayed with water or submerged into water. 

 

Do not use any detergents or cleaning solutions. The unit could be damaged. Chemical 
substances could negatively affect the unit's plastic components. 

10.2 

Air filter 

The air filter should be cleaned regularly removing dust and dirt to avoid: 

 

Carburetor malfunction 

 

Starting problems 

 

Reduced engine power 

 

Unnecessary wear to engine parts 

 

Abnormal fuel consumption 

 
Cleaning the air filter: 

 

Dismantle the air filter cover and remove the air filter. 

 

Wash in clean, warm soapy water. 

 

Ensure that the filter is dry before refitting. 

 

An air filter used for a long period of time can never be cleaned completely. Therefore it is 
necessary to replace the air filter from time to time with a new filter. 

Attention!  Do  not  ever  use  the  unit  without  its  air  filter.  The  filter  must  be 
kept clean. A damaged filter must be replaced with a new one. 

 

 

Summary of Contents for POWERPLUS POWEG8012















Reviews: