background image

 

POWEG8012 

EN

 

Copyright © 2021 VARO 

P a g e

 | 

3

 

www.varo.com 

BRUSH CUTTER 42.7CC 
POWEG8012 

1  APPLICATION 

The brush cutter is, depending on the assembled cutting tools, intended to mow lawns or 
pastures, to trim scrub, shrubs, bushes and very small trees for private use. De device cannot 
be used for other purposes. The manufacturer will no longer be liable when the device is used 
for a purpose other than what is intended or if it is modified. Please take the safety guidelines, 
the assembly and operation manual, as well as the general conditions for the prevention of 
accidents into account.  

WARNING!  Read  this  manual  and  general  safety  instructions  carefully 
before  using  the  appliance,  for  your  own  safety.  Your  power  tool  should 
only be passed on together with these instructions. 

2  OVERVIEW COMPONENTS (FIG A) 

1. 

Cutting attachment 

2. 

Metal cutting blade 

3. 

Protective cover  

4. 

Quick release latch 

5. 

Shaft housing 

6. 

Two-handed fork handle 

7. 

On / Off stop control 

8. 

Safety switch 

9. 

Gas lever 

10.  Belt eye 

11.  Belt 
12.  Sparkplug 
13.  Choke 
14.  Muffler 
15.  Fuel tank 
16.  Fuel cap 
17.  Air filter cover 
18.  Gearbox cover 
19.  Primer bulb 

3  PACKAGE CONTENT LIST 

 

Remove all packing materials 

 

Remove remaining packaging and transit supports (if existing) 

 

Check the completeness of the packing content 

 

Check the appliance, the power cord, the power plug and all accessories for transportation 
damages. 

 

Keep the packaging materials as far as possible till the end of the warranty period. 
Dispose it into your local waste disposal system afterwards. 

WARNING  Packing  materials  are  no  toys!  Children  must  not  play  with 
plastic bags!  Danger of suffocation! 

1 x brush cutter  
1 x double shoulder harness 
1 x trimmer line 
1 x cutting blade  
1 x spark plug socket  

1 x double head screwdriver  
1 x double open spanner 
2 x hex key 
2 x strap 
1 x bottle 

When parts are missing or damaged, please contact your dealer. 

 

 

Summary of Contents for POWERPLUS POWEG8012















Reviews: