background image

 

POWDP15210 

EN

 

Copyright © 2020 VARO 

P a g e

 | 

9

 

www.varo.com 

9.2 

Battery capacity indicator (Fig. 1a) 

There are battery capacity indicators on the battery pack, you can check the capacity status of 
the battery if you squeeze the button (12). Before using the machine, please press switch 
trigger to check if the battery is full enough for properly working. 
Those 3 LED might show the status of the capacity level of the battery: 
3 LED’s are litt: Battery fully charged 
2 LED’s are litt: Battery 60% charged 
1 LED is litt: Battery almost discharged 

9.3 

Inserting and removing the battery (Fig 2) 

WARNING: Before making any adjustments ensure the drill is switched off 
with the direction of rotation selector in the centre position 

 

Remove the battery: press the battery release latch in and at the same time pull the 
battery pack off. 

 

To insert the battery, push the battery pack onto the contacts of the tool. 

9.4 

Installing and Removing a Bit and a Drill (Fig 3) 

This drill has a keyless chuck to prevent the bit or drill from loosening

 

and allows you to hand 

tighten or release drill bit in the chuck jaws 

 

Turn ring A anticlockwise with the other hand until the drill chuck opening is large enough 
to accept the tool. 

 

Insert the drill or the screwdriver bit into the drill chuck. 

 

Turn ring A clockwise until the tool is clamped tightly. 

Remove the tool in the opposite way. 

9.5 

Switch (4) 

The drill is started and stopped by depressing and releasing the ON/OFF switch trigger. 

9.5.1 

Switch lock (Fig 4) 

The switch trigger can be locked in the center position. 
This helps to reduce the possibility of accidental starting when not in use. To lock the switch 
trigger, place the direction of rotation selector in the center position. 

9.5.2 

Direction of rotation (Fig 5) 

Direction of rotation is controlled by the direction of rotation selector located above the switch 
trigger. 

9.5.2.1 

Clockwise rotation: 

Right: To select forward rotation, release the on/off switch and push the forward/reverse lever 
to the left side of the tool. 

9.5.2.2 

Anticlockwise rotation: 

Left: To select reverse rotation, push the lever to the right side of the tool. 

9.5.3 

Variable speed 

This tool has a variable speed switch that delivers higher speed and torque with increased 
trigger pressure. 
Speed is controlled by the amount of switch trigger depression. 

Summary of Contents for Powerplus POWDP15210















Reviews: