VARO Powerplus GardenPro POWXG2016 Manual Download Page 7

 

POWXG2016 

EN

 

Copyright © 2015 VARO 

P a g e

 | 

7

 

www.varo.com 

8  OPERATING INSTRUCTIONS 

8.1 

Starting the engine 

Move at least 3 metres away from the place of refuelling. Place the hedge trimmer on a clean 
area of ground and make sure that the cutting tool does not come into contact with the ground 
or any other objects. 

Keep  the  blades  clear  of  everything  around,  since  they  will  start  moving  as 
soon as the engine starts. 

8.1.1 

Cold starting 

If the engine is cold or if it has been stopped for more than 5 minutes or if fuel has been added 
to the engine. 

 

Push the primer pump gently (7 to 10 times) until fuel begins to flow into it. (Fig. 1) 

 

Move the choke lever (4

) to position “

” (Fig. 2) 

(a)  choke lever 
(b)  open 
(c)  close 

 

Set the ignition switch to the “START” position. (Fig. 3) 

 

Hold the unit down firmly so that you will not lose control while cranking the engine. If not 
held down properly, the engine could make you lose your balance or swing the cutting 
blade into a nearby object or your body. 

 

Pull out the starter handle slowly (10 to 15 cm), and check the pressure. Pull strongly 
when you feel the pressure and start the engine.  

 

When the engine starts, return the choke lever to ” 

". Run the engine for approximately 

one minute at a moderate speed before moving up to full speed 

Note:  When  restarting  the  engine  immediately  after  stopping  it,  leave  the 
choke open. 

Note: Overchoking can make it hard to start the engine due to excess fuel. If 
the  engine  fails  to  start  after  several  attempts,  open  the  choke  and  pull  the 
rope again, or remove the sparking plug and dry it. 

8.1.2 

Hot starting 

Restarting immediately after the engine has stopped.If the engine does not start, repeat the 
above steps 

Do  not  pull  the  rope  to  the  end  or  return  it  by  releasing  the  knob.  This  can 
cause starter failures. 

8.2 

Stopping the engine 

 

Release the throttle lever completely. 

 

Move 

the engine switch to the “STOP” position. The engine will now slow down and stop 

(Fig. 4) 

Note: If the engine does not stop after moving the switch, close the choke to 
make it stop. 

Summary of Contents for Powerplus GardenPro POWXG2016















Reviews: