background image

 

POWAIR0803 

EN 

Copyright © 2014 VARO 

P a g e

 | 

5

 

www.varo.com 

Proper adjustment of the in-line lubricator is performed by placing a sheet of paper next to 
the exhaust ports and holding the throttle open approximately 30 seconds. The lubricator 
is  properly  set  when  a  light  stain  of  oil  collects  on  the  paper.  Excessive  amounts  of  oil 
should be avoided. 
In  the  event  that  it  becomes  necessary  to  store  the  tool  for  an  extended  period  of  time 
(overnight, weekend, etc.), it should receive a generous amount of lubrication at that time. 
The  tool  should  be  run  for  approximately  30  seconds  to  ensure  oil  has  been  evenly 
distributed throughout the tool. The tool should be stored in a clean and dry environment. 

  It is most important that the tool be properly lubricated by keeping the air line lubricator 

filled and correctly adjusted. Without proper lubrication the tool will not work properly 
and parts will wear prematurely. 

  Use the proper lubricant in the air line lubricator. The lubricator should be of low air flow 

or changing air flow type, and should be kept filled to the correct level. Use only 
recommended lubricants, specially made for pneumatic applications. Substitutes may 
harm the rubber compounds in the tools, O-rings and other rubber parts. 

IMPORTANT!!! 

If a filter/regulator/lubricator is not installed on the air system, air operated tools should be 
lubricated at least once a day or after 2 hours work with 2 to 6 drops of oil, depending on 
the work environment, directly through the male fitting in the tool housing. Fig. 1 
1. 

Tool 

2. 

Quick connector 

3. 

Quick coupler 

4. 

Air hose 

5. 

Quick connector 

6. 

Quick coupler 

7. 

Lubricator 

8. 

Regulator (0-8.5 bar) 

9. 

Filter 

10. 

Cut-off valve 

11. 

Air compressor 

LOADING AND OPERATION 

WARNING:  Ensure  you  read,  understand  and  apply  safety  instructions 
before use. 

1. 

Connect the tool to the air hose. 

2. 

Press the trigger to operate the tool.  

3. 

The flow of air may be regulated by adjusting flow valve at the base of the handle. 

4. 

Ensure the air supply is clean and does not exceed 90psi while operating the tool. 
Too high an air pressure and unclean air will shorten the product life due to 
excessive wear, and may be dangerous causing damage or personal injury. 

DO  NOT  use  any  additional  force  upon  the  wrench  in  order  to  remove  a 
nut. 

DO  NOT  allow  wrench  to  free  run  for  an  extended  period  of  time  as  this 
will shorten its life. 

Summary of Contents for POWERPLUS AIR POWAIR0803









Reviews: