manualshive.com logo in svg

Vari Lite VL2B, Service Manual, Page: 88 / 310

Share
Download
Vari Lite VL2B Service Manual Download Page 88

3-42

V

ARI

*L

ITE® 

-

 

VL2B

 AND 

VL2C

 

S

POT 

L

UMINAIRE 

S

ERVICE 

M

ANUAL

CONFIDENTIAL

02.9631.0010

15 Jan 98

3.3 

Luminaire Maintenance Procedures

3.3.1 

Brightness/Filter Bulkhead Maintenance

3.3.1.1 

Brightness/Filter Bulkhead Removal and
Replacement

Parts:

1 EA

ASSY, VL2B BRIGHTNESS/FOCUS BULKHEAD,
(22.9631.0028)

1 EA

ASSY, VL2C BFB (BRIGHTNESS/FOCUS BULKHD)
(22.9637.0005)

Tools:

Screwdriver, Phillips #2

To remove and replace brightness/focus bulkhead:,

BRIGHTNESS/FOCUS BULKHEAD

COLOR FILTER BULKHEAD

FIT TAB ON RETAINER
TO HOLE IN BRIGHTNESS

6-32X3/8"PPZ SCREW 

BULKHEAD RETAINING
ADAPTER (VL2C ONLY) 

INSTALLATION OF COLOR

BRIGHTNESS/FOCUS BULKHEAD

NOTE:

MUST BE INSTALLED PRIOR TO

FILTER BULKHEAD

2BTB1

FILTER BULKHEAD TAB

Figure 3-1.  Brightness/Focus Bulkhead Removal and Replacement

Step 1.

Remove power to luminaire.

Step 2.

Remove head covers.

a. Remove 20, 6-32x5/16"PFB screws that secure head covers

to rails.  Remove both head covers.

Summary of Contents for VL2B























































































































































































































































































































Reviews:

No comments