background image

Vantron 

| Embedded in your success, Embedded in your better life

 

World-leading provider of embedded/IoT products and solutions 

  Vantron | G202 User Manual       

 

 

 

38   

 

   

      www.vantrontech.com 

3.5.3 4G/LTE 

Before you configure for 4G/LTE, be sure to install the activated SIM card in the slot. In the 
4G/LTE page, you can access the general and advanced settings, the connection log, and 
traffic of the cellular network. 

Confirm with your sales representative whether the 4G module is AT&T or Verizon pre-
certified or not. If so, when you apply for SIM cards from the carriers,   

°

 

provide Verizon with the pre-certified module name 

VT-MOB-CELL-mPCIe

°

 

provide AT&T with the pre-certified module name 

VT-MOB-MPCIE-4G

Remember to ask the carriers for the APN which needs to be filled in the system during 4G 
setup. 

If you have inserted an activated SIM card in the slot, the SIM card information will display 
on the top of the page, including signal strength, IP, and IMEI. While register status and 
other general information will display at the bottom of the page. 

 

Description of the numbered areas 

1.

 

Enable/disable 4G/LTE service 

2.

 

Input *99***1# for AT&T SIM card and *99***3# for Verizon SIM card 

3.

 

Input the APN provided by the carrier 

4.

 

Enter the username provided by the carrier for PAP/CHAP authentication 

5.

 

Enter the password provided by the carrier for PAP/CHAP authentication 

6.

 

Click 

Advanced Setting

 for more configuration options 

Summary of Contents for G202














































































Reviews: