background image

Vantron 

| Embedded in your success, Embedded in your better life

 

World-leading provider of embedded/IoT products and solutions 

  Vantron | G202 User Manual       

 

 

 

12   

 

   

      www.vantrontech.com 

1.5

 

Serial Port Introduction 

 

There are two serial ports on the terminal block, one is RS485, the other is configurable to 
RS485 (default) or RS232. Only when users choose to configure the other one to RS232 will 
serial debugging be available. Yet RS232 is used for serial communication under normal 
circumstances. To activate the debug mode, users can long press the debug button before 
power application till output data is displayed on the PC. 

If users choose to configure both serial ports to RS485, serial debugging is not available. 
Under such circumstances, debugging over Ethernet is an option. 

Definition of the terminal pins: 

No. 

(From left to right) 

Pin name 

Port 

Type 

Definition 

GND1 

/dev/ttyS1 

NC 

RS485 isolator grounding 

I/O 

RS485-A signal 

I/O 

RS485-B signal 

RX 

/dev/ttyS0 

RS232 RXD signal 

TX 

RS232 TXD signal 

GND2 

RS232 isolator grounding 

Input the following command lines  in the 

Terminal

  page of VantronOS  for  serial 

communication: 

1.

 

For RS232 communication: 

~# microcom /dev/ttyS0 -s 115200

 

2.

 

For RS485 communication: 

~# microcom /dev/ttyS1 -s 115200

 

 

Please refer to 

Appendix B

 for the definition of the acronyms mentioned above. 

Summary of Contents for G202














































































Reviews: