Vanguard VMH3000TNSA Owner'S Operation And Installation Manual Download Page 1

Save this manual for future reference.

OWNER’S OPERATION AND INSTALLATION MANUAL

VENT-FREE NATURAL GAS

MINI-HEARTH

®

 HEATER

VMH3000TNSA

15,000 to 30,000 Btu/Hr

with Thermostat

This appliance may be installed in an aftermarket*, permanently located, manufac-
tured (mobile) home, where not prohibited by state or local codes.
This appliance is only for use with the types of gas indicated on the rating plate.
This appliance is not converrtible for use with other gases.

WARNING: If the information in this manual is not
followed exactly, a fire or explosion may result
causing property damage, personal injury, or
loss of life.

— Do not store or use gasoline or other

flammable vapors and liquids in the vicinity
of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.
• Do not touch any electrical switch; do not

use any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas
supplier’s instructions.

• If you cannot reach your gas supplier, call

the fire department.

— Installation and service must be performed

by a qualified installer, service agency, or the
gas supplier.

WARNING: Improper installa-
tion, adjustment, alteration,
service, or maintenance can
cause injury or property dam-
age. Refer to this manual for
correct installation and op-
erational procedures. For as-
sistance or additional infor-
mation consult a qualified in-
staller, service agency, or the
gas supplier.

WARNING: This is an unvented
gas-fired heater. It uses air
(oxygen) from the room in
which it is installed. Provisions
for adequate combustion and
ventilation air must be pro-
vided. Refer to 

Air For Com-

bustion and Ventilation sec-
tion on page 5 of this manual.

®

Shown with Optional

Mantel Which Features

a Built-In Base

*Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer.

Summary of Contents for VMH3000TNSA

























Reviews: