Vanguard MDVFST Owner'S Operation And Installation Manual Download Page 1

Save this manual for future reference.

DIRECT-VENT GAS FIREPLACE

OWNER’S OPERATION AND INSTALLATION MANUAL

®

MDVFST (See Thru) fireplace with manual variable blower, ON/OFF hand-held remote control,

electrical junction box, gas flex line and equipment shutoff valve.

This appliance may be installed as an OEM installation in a manufactured (mobile) home and must
be installed in accordance with the manufacturer's instructions and the Manufactured Home
Construction and Safety Standard, 

Title 24 CFR, Part 3280 in the United States or the Mobile Home

Standard, 

CAN/CSA Z240 MH Series, in Canada.

This appliance is only for use with the type of gas indicated on the rating plate. A conversion kit is
supplied with the appliance.

— Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any
other appliance.

— WHAT TO DO IF YOU SMELL GAS :

• Do not try to light any appliance.
• Do not touch any electrical switch;
• Do not use any phone in your building.
• Immediately call your gas supplier from a

neighbor’s phone.  Follow the gas supplier’s
instructions.

• If you cannot reach your gas supplier, call the

fire department.

— Installation and service must be performed by a

qualified installer, service agency, or the gas
supplier.

SAVE THIS BOOK

This book is valuable. In addition to instructing
you on how to install and maintain your appli-
ance, it also contains information that will
enable you to obtain replacement parts or
optional accessory items when needed. Keep
it with your other important papers.

WARNING: Improper installation,
adjustment, alteration, service, or
maintenance to this appliance can
cause injury or property damage.
Refer to this manual. For assistance
or additional information consult a
qualified installer, service agency,
or the gas supplier.

CHECK LOCAL CODES PRIOR TO INSTALLATION

WARNING: If the information in these instruc-
tions is not followed exactly, a fire or explosion
may result causing property damage, personal
injury, or loss of life.

WARNING: This direct-vent gas fire-
place series is intended for use with
Natural or Propane/LP gas only. Do
not attempt to burn any solid fuels
in these appliances.

This fireplace meets
the construction and

safety standards of

H.U.D. for application

in mobile homes when

installed according to

these instructions.

This appliance is

shipped ready for natural

gas installation. The

propane/LP conversion

parts are included.

Summary of Contents for MDVFST





























Reviews: