Lighting Instructions
WARNING
: If you do not follow these instructions exactly, a fire or explosion may result causing
property damage, personal injury or loss of life.
Fig 1
Fig 2
Fig 2A
FOR YOUR SAFETY, READ BEFORE LIGHTING
A. This appliance has a pilot which must be lighted by hand or by remote control. Follow these instructions exactly. To
save gas, turn the pilot off when not using the appliance for a prolonged period of time.
B. BEFORE LIGHTING, smell all around the appliance area for gas. Be sure to smell next to the floor because some gas
are heavier than air and will settle on the floo
r.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbo
r’s phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplie
r
, call the fire department.
C. Use only your hand to push in or turn the control knobs. Never use tools. If the knobs will not push in or turn by hand,
don’t try to repair them; call a qualified service technician. Force or attempted repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water
. Immediately call a qualified servi
ce technician to inspect
the appliance and to replace any part of the control system and any gas control, which has been under water.
LIGHTING INSTRUCTIONS
1. STOP! Read the safety information above. Dependent on model, switch #1 may be mounted directly to valve see Fig 2A.
TO TURN OFF GAS TO APPLIANCE
2. SET ON/OFF SWITCH (1) TO “OFF” POSITION.
W
ait five (5) minutes to clear out any gas, then smell for gas, including near the floo
r. If you smell gas, STOP! Follow
“B” in the safety information above on this label. If you don’t smell gas, go to the next step.
3. AUTOMA
TIC IGNITION (fig. 1): Locate the pilot (fig 3.) inside of firebox at Left Hand side.
ON/OFF switch (1) in ON position, MAN-knob (2) in ON position; set Flame
Adjustment knob (3) to lowest setting
(
);
On the remote control handset, press and hold the ‘off ’ button and (large flame)
simultaneously; a short
acoustic signal confirms the start has begun;
Further short acoustic signals indicate the ignition process is in progress;
When the pilot is lit, the Flame Adjustment knob (3) will automatically rotate to the highest setting.
Press the (small flame)
on the remote control handset to reduce the flame height.
4. MANUAL
IGNITION (fig. 2):
W
ith the window off, locate the pilot (fig. 3)
inside of firebox at Left Hand side;
ON/OFF switch (1) in ON position, MAN-knob (2) in MAN position;
Set Flame Adjustment knob (3) to the lowest setting
(
);
Push down the metallic core (4) with a pen or similar instrument; this will establish the pilot gas flow;
Light gas at the pilot (5) with a match;
Continue holding down metal core (4) for about 10 seconds; after release, pilot should remain lit;
If the pilot will not stay lit after several tries, turn the gas control knob (3) to “OFF”
(
)
and call your local
service technician or gas supplier.
Reinstall the window and set the MAN-knob (2) to “ON”; turn Flame
Adjustment knob (3) up
(
)
or down
manually or use the up/down ‘flame’ buttons on the remote control handset to adjust the
flame height.
•
•
•
•
•
•
•
•
•
•
Fig 3
1. AUTOMATIC SHUT
-OFF (using the remote control handset):
Press and hold the (small flame)
on the remote control handset to shut-off the main burner gas flow;
Press “OFF” button on remote handset to shut-off the appliance, including pilot flame.
2. MANUAL SHUT-OFF (using only the ON/OFF switch (1))
Press “O” the ON/OFF switch (1) to shut-off the appliance.
•
•
•
Alternate
position
33
Summary of Contents for LEGEND G4 780IN (NG)
Page 40: ...40...