background image

INSTALLATION & OWNER’S MANUAL

Gravity Vent Gas Insert Fireplace
738JN (natural gas) & 738JP (propane gas)

Legend G3

This appliance may be installed in an after-
market permanently located, manufactured 
(mobile) home where not prohibited by local 
codes.
This appliance is only for use with the type 
of gas indicated on the rating plate. This 
appliance is not convertible for use with 
other gases, unless a certifi ed kit is used.

HOT GLASS

 WILL 

CAUSE BURNS.

DO NOT TOUCH 

GLASS 

UNTIL COOLED.

NEVER 

ALLOW CHILDREN 

TO TOUCH GLASS.

DANGER

!

A barrier designed to reduce the risk of burns from the hot 
viewing glass is provided with this appliance and shall be 
installed for the protection of children and other at-risk 
individuals.

Ce guide est disponible en français sur demande.

This appliance is a domestic room-heating 
appliance. It must not be used for any other 
purposes such as drying clothes, etc.

This appliance is suitable for installation in 
a bedroom or bed sitting room.

INSTALLER

Leave this manual 
with the appliance.

CONSUMER

Retain this manual 
for future reference.

Please read this manual 

BEFORE 

installing and 

operating this appliance.

— Do not store or use gasoline or other 

fl ammable vapors and liquids in the 
vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

 

▪ Do not try to light any appliance.

 

▪ Do not touch any electrical switch; do 

not use any phone in your building.

 

▪ Leave the building immediately.

 

▪ Immediately call your gas supplier from 

a neighbor’s phone. Follow the gas 
supplier’s instructions.

 

▪ If you cannot reach your gas supplier, 

call the fi re department.

— Installation and service must be 

performed by a qualifi ed installer, 
service agency or the gas supplier.

  

!

  WARNING

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly 
could result in serious injury, death, or 
property damage.

This manual contains instructions to install the

 

ENGINE ONLY. 

A front is

 also REQUIRED 

to 

complete this installation. A barrier screen is pro-
vided with the front. 

Refer to the manual sup-

plied with the front for installation.

4005338-11

©2018, Miles Industries Ltd.

Summary of Contents for Legend G3











































Reviews: