manualshive.com logo in svg

Valcourt FG00001, Installation Instructions Manual

Share
Download
Valcourt FG00001 Installation Instructions Manual Download Page 50

Page 50

Installation Manual - L48

ENGLISH

7. Crushed Glass Media Installation

7.1  Screen barrier and glass door removal

CAUTION

The screen barrier must be handled with care. It is made as invisible as possible. A slight 

deformation could impair its invisibility properties. Avoid putting pressure on the mesh 

and make sur the screen weight is never supported by the mesh.

1.  Lift the barrier up 

approximately 1/4-in with 
one hand under the lower 
barrier frame edge to 
disengage the lower flange

A

DETAIL A

2.  Grasp the top of the 

barrier and pull forward to 
disengage it. Remove the 
barrier by pulling straight 
forward.

CAUTION

The glass door is wide and heavy and can be difficult to install or remove by 

a single person. It is recommended that two people remove the glass door.

CAUTION

Sharp objects. Gloves are strongly recommended.

3.  Locate the glass door tool 

(secured to the top of the 
fireplace for shipping). Use the 
tool as a lever to release the 
bottom of the glass door as 
shown.

     

C

DETAIL C

D

DETAIL D

Summary of Contents for FG00001































































Reviews:

No comments

Brands by name

Popular brands

Load more brands