Vaisala IRIS User Manual Download Page 18 | Manualshive

Page: 18 / 394

Vaisala IRIS User Manual Download Page 18

3. Configuring IRIS Products

3.1 Configuring Products

IRIS Radar products provide information that can be used directly for weather nowcasting
and forecasting. You configure the products in IRIS Radar.
IRIS products can display radar data in many ways. For example:

• The

CAPPI

product shows the distribution of a radar parameter, such as reflectivity or

spectrum width, at a constant altitude.

• The

TOPS

product shows a color contour map of the height of a selected reflectivity

surface.

• The

RAIN1

and

RAINN

products show the accumulation of precipitation over selectable

time periods.

• The

WARN

product checks other IRIS products to determine if there is significant

weather, such as wind shear greater than a threshold amount.

Each product is associated with a configured task. Tasks collect information from signal
processors and store the data on disk in ingest files.
For more information, see

IRIS Radar User Guide

.

More information

‣

QLW Live Action Tool: Product Generation and Display (page 208)

IRIS Product and Display User Guide

M211319EN-H

16

RESTRICTED

«
...
16
17
18
19
20
...
»

Summary of Contents for IRIS











































































































































































































































































































































































































Reviews:

No comments