Vaisala IRIS User Manual Download Page 142

Page: 142 / 394

Because

DWELL

products show the integrated time history of echoes, they are a useful

alternative to the

TRACK

product.

In airborne target detection,

DWELL

is used to track and automatically warn about the

presence of aircraft or migrating bird flocks.

5.3.1 DWELL Algorithm Examples

DWELL

is comprised of a product and composites successive images of a product in time.

Moving targets show a "streak" on the display.
The example shown here is for

DWELL

applied to

PPI

products. The last (most recent)

PPI

product in the

DWELL

sequence is shown below. It shows a squall line in

dBZ

. The line was

moving from East to West and developing/decaying as it traveled.

IRIS Product and Display User Guide

M211319EN-H

140

RESTRICTED

Summary of Contents for IRIS











































































































































































































































































































































































































Search results

Summary of Contents for IRIS

Reviews:

Related manuals for IRIS

Brands by name

Popular brands

Vaisala IRIS, User Manual

Search results

Summary of Contents for IRIS

Reviews:

Related manuals for IRIS

Brands by name

Popular brands