manualshive.com logo in svg

Vaisala AWS310-SITE, Configuration And Maintenance Manual

Share
Download
Vaisala AWS310-SITE Configuration And Maintenance Manual Download Page 34

3. In 

Serial Port

, select the 

COM port

 used for the service connection. 

4. To save the changes, select 

Save

.

5. To close the window, select 

Close

.

4.4 Station Settings

The weather station is pre-configured with the ordered features during manufacturing.
However, you must configure certain parameters, such as site information and messaging
settings. You can also add features later by installing additional preconfigured sensors and
changing the appropriate configuration parameters accordingly.

Before you make any changes to an existing system, download the current

setup file and back up the station parameters in case something goes wrong.

CAUTION!

AWS310-SITE Configuration and Maintenance Manual

M211828EN-C

32

Summary of Contents for AWS310-SITE

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands