manualshive.com logo in svg

Vaisala AWS310-SITE, Configuration And Maintenance Manual

Share
Download
Vaisala AWS310-SITE Configuration And Maintenance Manual Download Page 15

2. Product Overview

2.1 Vaisala Automatic Weather Station

AWS310-SITE

Vaisala Automatic Weather Station AWS310

‑

SITE automatically measures, processes, and

stores meteorological data for airport use. AWS310

‑

SITE is designed for permanent

installation.
The QML data logger inside the weather station enclosure receives measurement data from
the sensors and calculates basic meteorological variables. It also monitors sensor status,
performs data quality control, and formats data for output in application-specific formats.
These values are transmitted to the Vaisala AviMet system, where they are further processed
and displayed to the user.
AWS310

‑

SITE requires only a minimal amount of maintenance and can be trusted to perform

effectively in all weather conditions and climates. The modular design of the station allows
easy integration of additional sensors after the initial purchase and permits quick
replacement of individual components, reducing downtime and overall operating cost.
Vaisala offers a variety of services related to AWS310

‑

SITE, for example:

• Factory inspection test
• Factory acceptance test
• Site acceptance test
• Installation
• Training
• Technical support
• High-quality sensor calibration (including ISO/IEC 17025-accredited calibration)

2.1.1 AWS310-SITE Observations

Depending on the installed sensors, AWS310

‑

SITE can measure the following weather

parameters:

• Air temperature and humidity
• Barometric pressure
• Cloud height
• Precipitation amount
• Present weather and visibility
• Soil moisture
• Soil temperature
• Solar radiation
• Sunshine duration (calculated)
• Wind speed and direction

You can use AWS Client to work with the QML data logger, for example, to set station-
specific parameters and to download the daily log files.

Chapter 2 – Product Overview

13

Summary of Contents for AWS310-SITE

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands