manualshive.com logo in svg

Vaisala AWS310-SITE, Configuration And Maintenance Manual

Share
Download
Vaisala AWS310-SITE Configuration And Maintenance Manual Download Page 114

4. To activate the new configuration, reset the QML data logger. Select 

Maintenance > 

Reset > Immediate

.

5.16 QMT Maintenance

Check the cabling once a year. Check that the cable visible on the ground is in good shape.
The subsurface temperature sensor does not need regular maintenance. If you remove the
sensor from the ground, clean the dirt accumulation on the sensor surface using a soft, lint-
free cloth moistened with mild detergent.
If the sensor malfunctions, replace it. The sensor has no replaceable parts.

5.16.1 Adding QMT110 to System

These instructions apply to QMT107 and QMT110.
Before configuring the new sensor, complete the mechanical installation.

1. In AWS Client, select 

Settings > Parameters > Static

.

2. In the 

CFG

 parameter set, select 

QMT110_1

 or 

QMT110_2

.

3. To enable the sensor, type 

1

 in the 

Value

 field, and select 

Save

.

4. To activate the new configuration, reset the QML data logger. Select 

Maintenance > 

Reset > Immediate

.

5.17 DRS511 Maintenance

Periodic maintenance for DRS511 includes:

• Checking the sensor position once a year before the wintertime.

There is no need to calibrate the optical measurement of DRS511 regularly. However,
calibration is recommended:

• After grinding the sensor surface
• When the sensor is easily accessible due to other work

5.17.1 Checking DRS511 Position

Vaisala Installation Plate (210764) or spirit level

AWS310-SITE Configuration and Maintenance Manual

M211828EN-C

112

Summary of Contents for AWS310-SITE

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands