background image

Notes on the documentation 2

0020221300_04 uniSTOR HP Installation and maintenance instructions

5

2

Notes on the documentation

2.1

Observing other applicable documents

Always observe all the operating and installation instruc-
tions included with the system components.

2.2

Storing documents

Pass these instructions and all other applicable docu-
ments on to the end user.

2.3

Validity of the instructions

These instructions apply only to:

Product article number

VIH RW GB 150 BES

0010019224

VIH RW GB 200 BES

0010019225

VIH RW GB 250 BES

0010019226

VIH RW GB 300 BES

0010019227

2.4

Benchmark

Vaillant is a licensed member of the Benchmark Scheme.

Benchmark places responsibilities on both manufacturers
and installers. The purpose is to ensure that customers are
provided with the correct equipment for their needs, that it is
installed, commissioned and serviced in accordance with the
manufacturer’s instructions by a competent person approved
at the time by the Health and Safety Executive and that it
meets the requirements of the appropriate Building Regu-
lations. The Benchmark Checklist can be used to demon-
strate compliance with Building Regulations and should be
provided to the customer for future reference.

Installers are required to carry out installation, commission-
ing and servicing work in accordance with the Benchmark
Code of Practice which is available from the Heating and
Hotwater Industry Council who manage and promote the
Scheme.

Benchmark is managed and promoted by the Heating and
Hotwater Industry Council.

For more information visit www.centralheating.co.uk

3

Product description

3.1

Serial number

1

You can find the serial number on the data plate

(1)

, which is

located on the cylinder below the electronics box.

3.2

Information on the identification plate

The identification plate is attached to the product at the fact-
ory.

The identification plate keeps record of the country in which
the product is to be installed.

This product meets the requirements of standard EN
12897:2006.

3.3

CE marking

The CE marking shows that the products comply with the
basic requirements of the applicable directives as stated on
the declaration of conformity.

The declaration of conformity can be viewed at the manufac-
turer's site.

Summary of Contents for uniSTOR VIH RW GB BES Series

























Reviews: