Vaillant auroMATIC VRS 560 System Manual Download Page 25

Page: 25 / 68

Manual - Solar hot water systems

5.1.2

Technical data of the auroSTOR solar cylinder

Entry

Unit

VIH S GB 200 S

VIH S GB 250 S

VIH S GB 300 S

Cylinder:

Size

l 200

250

300

Maximum water supply pressure

bar

Operating pressure

bar

3.5

Pressure limiting valve

bar

3.5

Expansion relief valve

bar

6.0

Hot water expansion vessel admission pressure

bar 4.0

Temperature and pressure relief valve

°C/bar

95 / 7.0

Net weight

Weight (full)

245

310

340

Height mm

1499

1789

2109

Cylinder connections:

Cold water supply

22 mm pressure pipe

Hot water connection

22 mm pressure pipe

Pressure-controlled cold water outlet

22 mm pressure pipe

Secondary return

Inches

G 3/4

Flow (boiler/solar circuit)

22 mm pressure pipe

Return (boiler/solar circuit)

22 mm pressure pipe

Electrical connections:

3 kW immersion heater (according to ENBS 60335)

230/240 V, 50 Hz

Length of the immersion heater

430

Motorised 2 port valve

230/240 V, 50 Hz

Cylinder thermostat

230/240 V, 50 Hz

Thermal cut out for solar pump

230/240 V, 50 Hz

Heating coil:

Heat loss

kW/24 h

1.9

2.1

2.4

Heat up time (boiler part)

mins

Recovery (boiler part)

mins

Table 5.4 Technical data of the auroSTOR solar cylinder

Note!
The heat-up time is based on a primary flow
rate of 9 l/min at 80 °C.
Temperature rise from 15 °C to 65 °C

Installation 5

Summary of Contents for auroMATIC VRS 560





































































Search results

Summary of Contents for auroMATIC VRS 560

Reviews:

Vaillant auroMATIC VRS 560, System Manual, Page: 25 / 68

Search results

Summary of Contents for auroMATIC VRS 560

Reviews: