Vaderstad Rapid RDA 400S Original Instructions Manual Download Page 93

Page: 93 / 138

RDA 400S

27.06.2011
ver.2

5.2

Inspecting the drill's towing eyelet

Figure 5.6

5.2.1

Alternative drawbar eyes

50 mm drawbar eye diameter (standard).

40 mm drawbar eye diameter (standard).

Ball hitch, 80 mm diameter.

Swivel drawbar eye, 57 mm diameter.

5.2.2

Re-tightening of screw connections

The screw connections (E) of the drawbar eye must be re-tightened at regular intervals. Tightening
torque 277 Nm.

5.2.3

Wear limit

When the diameter of the drawbar eye has increased by 2.5 mm, the wear limit has been reached
and it is time to change the eye.

When fitting a new eye, new screws must also be used. The screws (E) must then be tightened to
a torque of 277 Nm. Use a torque wrench.

NOTE!

Never weld a drawbar eye, as this can considerably reduce its strength!

Max +2.5 mm

Summary of Contents for Rapid RDA 400S











































































































































Search results

Summary of Contents for Rapid RDA 400S

Reviews:

Related manuals for Rapid RDA 400S

Brands by name

Popular brands

Vaderstad Rapid RDA 400S, Original Instructions Manual

Search results

Summary of Contents for Rapid RDA 400S

Reviews:

Related manuals for Rapid RDA 400S

Brands by name

Popular brands