Vaderstad Rapid RDA 400S Original Instructions Manual Download Page 24 | Manualshive

Page: 24 / 138

background image

Instructions and settings

24

27.06.2011

ver. 2

3.5

Hose length and hose holder adjustment

Figure 3.13

The seed drill is equipped with a folding hose holder.

The holder can be fitted in different positions along the drawbar, and it should be located as close
to the tractor as possible to work best. The hose holder should also, in most cases, be pulled out
to its full length. Try to get the support for the hoses close to the drawbar eye or the intermediate
packer turning point.

The excess length of the hoses is formed into a loop beneath the platform and the hoses are
clamped by the hose holder.

!

When the hydraulic hoses are connected to the tractor, the hose holder must be folded forward.
Choose a suitable location by moving the pin, see position A. The lengths of the hoses must be
arranged so that they hang free, even during sharp turns.

!

When the hydraulic hoses are disconnected from the tractor, the hose holder must be folded
back. Keep the holder in its upright position with the pin, see position B. The hydraulic hoses
can now hang in the hose holder without the quick-release couplings dragging on the ground
and getting dirty.

A

B

«
...
22
23
24
25
26
...
»

Summary of Contents for Rapid RDA 400S











































































































































Reviews:

No comments

Related manuals for Rapid RDA 400S

Brand: Tacx Pages: 2

Brand: C.E. Nierhoff & Co Pages: 7

D-MAS HyperSat 2540

Brand: DanMedical Pages: 103

Brand: ACE INSTRUMENTS Pages: 2

Brand: ODA Pages: 103

Brand: Gaspardo Pages: 16

Brand: Gastrodomus Pages: 4

Brand: HANYOUNG NUX Pages: 2

Brand: Gastrodomus Pages: 39

Brand: iHealth Pages: 8

Brand: Maico Pages: 55

Brand: Maico Pages: 38

Brand: Maico Pages: 2

Brand: MAHA Maschinenbau Haldenwang Pages: 13

Brand: Rane Pages: 6

Brand: Rane Pages: 27

Brand: Ranger Products Pages: 6

Brand: Rane Pages: 88

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands