Vadem Clio Service Manual Download | Manualshive

Page: 99 / 106

background image

CLIO Service Manual

CLIO Tear-down & Rebuild

5.18.2. I

NVERTER

PWB

U

NIT

–

R

EFIT

1.

Solder the backlight wires to the Inverter PWB Unit (11), taking care to solder them in the
proper order.

2.

Place the Inverter PWB Unit (11) into position, then rotate 90 degrees clockwise (to
vertical) and re-fasten the orange Display Connection FPC plug. Rotate the Inverter
PWB Unit (11) back into position.

3.

Insert the two #1 Phillips head (10)(K2.2x6.5) head screws in their holes, and torque
them to 0.2N.M using a #1 Phillips head screwdriver.

4.

Follow the Display Top refit procedure, above. Be sure to coil the Display connection
FPC (8) twice before plugging it in if it was not pre-coiled.

5.19. D

ISPLAY

C

ONNECTION

FPC

–

R

EMOVE

&

R

EFIT

Please refer to photos 5, 12, 22 in Chapter 2.

5.19.1. D

ISPLAY

C

ONNECTION

FPC

–

R

EMOVAL

1.

Follow the Display Top removal procedure, above.

2.

Unplug the orange Display Connection FPC (8) from the lower right corner of the Main
PWB Unit (50).

3.

Follow the Display Bezel removal procedure, above.

4.

Follow Steps 1-4 of the Inverter PWB Unit (11) removal procedure, above.

5.

Unplug the Display Connection FPC (8) from the LCD Unit (66) and carefully peel away
the tape securing the Display Connection FPC (8) to the LCD Unit (66). Store the
Display Connection FPC (8) in a secure location.

5.19.2. D

ISPLAY

C

ONNECTION

FPC

–

R

EFIT

1.

Plug the Display Connection FPC (8) into the LCD Unit (66), taking care to avoid
damaging the plug.

2.

Secure the flex circuit (8) in position by taping it to the LCD Unit (66).

3.

Follow Steps 2-4 of the Inverter PWB Unit refit procedure, above.

4.

When replacing the Display Connection FPC (8), be sure to coil it twice just outside the
LCD Bezel opening if the FPC (8) did not come pre-coiled.

5.

Follow the Display Top refit procedure, above.

6.

Follow the Keyboard base Bottom refit procedure, above.

5.20. B

OTTOM

H

INGE

–

R

EMOVE

&

R

EFIT

Please refer to photos 4, 7, 9, 12, in Chapter 2.

5-13

The information contained in this document is confidential and the sole property of Vadem Inc. Written
permission must be obtained to reprint or use any of this information.

AUTHORED BY ANTHONY HERNANDEZ - (415)786-2081 - [email protected]

«
...
97
98
99
100
101
...
»

Summary of Contents for Clio











































































































Reviews:

No comments

Related manuals for Clio

Visionbook 14WR

Brand: UMAX Technologies Pages: 73

Toughbook CF-19KHRAG2M

Brand: Panasonic Pages: 91

visionbook 14WRx

Brand: UMAX Technologies Pages: 72

Aspire 7735ZG Series

Brand: Acer Pages: 13

Aspire 7535 Series

Brand: Acer Pages: 220

Brand: Acer Pages: 9

TravelMate 5335

Brand: Acer Pages: 313

TravelMate 5740

Brand: Acer Pages: 314

Extensa 5430 Series

Brand: Acer Pages: 176

Galaxy Book Pro NP935XDB-KC1UK

Brand: Samsung Pages: 105

Brand: Awood Pages: 33

Satellite L855-S5163

Brand: Toshiba Pages: 4

Satellite L855-S5155

Brand: Toshiba Pages: 4

Satellite L775D-S7340

Brand: Toshiba Pages: 4

Satellite L775D-S7330

Brand: Toshiba Pages: 4

Satellite L775D-S7226

Brand: Toshiba Pages: 4

Satellite L775D-S7224

Brand: Toshiba Pages: 4

Satellite L775D-S7222

Brand: Toshiba Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands