VADDIO RoboTRAK Integrator'S Complete Manual Download Page 66

Page: 66 / 74

Specifications

IR Camera

Operational Distance

12 to 50 ft (3.7 to 15.2 m)

Peak IR Sensitivity

850 nm

Horizontal range

±90°

Vertical Placement

7 to 15 ft (2.1 to 4.6 m)

Max. Vertical Offset

20°

Position Presets

Communication

10/100 Ethernet

Power

12 VDC, 3.0A

Height

6.3 in (163 mm)

Depth

5.5 in (145 mm)

Width

6.1 in (155 mm)

Weight

3.0 lbs (1.36 kg)

IR Source Lanyard

Battery Life

Up to 40 hrs (25 typical)

Charging time

About 4 hrs

Diameter

2 in (51 mm)

Depth

1.0 in (25 mm)

Weight

3.2 oz (91 g)

Lanyard length

24 in (610 mm)

System Mounting Weight

Mounted to Wall

15.3 to 16.4 lbs (6.95 to 7.45 kg)

Mounted to Ceiling

16.7 to 17.8 lbs (7.55

to 8.05 kg)

Weight varies depending on the video camera used.

Environmental and Room Requirements

Operating temperatute

0 °C to +24°C (32°F to 75°F)

Storage temperature

-5° to +60° C (23°F to

140°F)

Operating humidity

15% to 80% RH

(non-condensing)

Storage humidity

20% to 80% RH

(non-condensing)

Lighting Restrictions

No natural or halogen-based lighting, no IR-based communication systems

Video Camera – see specifications for the purchased camera

Integrator's Complete Guide to the RoboTRAK Presenter Tracking System

Summary of Contents for RoboTRAK











































































Search results

Summary of Contents for RoboTRAK

Reviews:

Related manuals for RoboTRAK

Brands by name

Popular brands

VADDIO RoboTRAK, Integrator'S Complete Manual

Search results

Summary of Contents for RoboTRAK

Reviews:

Related manuals for RoboTRAK

Brands by name

Popular brands