manualshive.com logo in svg

VADDIO 999-21100-009, Complete Manual

Share
Download
VADDIO 999-21100-009 Complete Manual Download Page 40

Operating the Camera with the RF Remote

The RF remote provides basic in-conference functionality – pan, tilt, zoom, presets, volume control, and
muting. You can also use it to get the camera's IP address. When you have the IP address, you can open
the camera's web interface.

Before you can use the remote, you will need to:

n

Install the batteries

n

Pair the remote with the camera

IntelliSHOT cameras are not compatible with IR remotes.

Installing the Batteries

The remote uses two AAA batteries.

1. Remove the cover from the back of the remote. You may need to press down on the inner edge while

sliding it off.

2. Install the batteries as shown in the diagram in the battery opening.

3. Slide and snap the cover back into place.

Pairing the Remote to the Camera

The camera does not recognize or respond to the remote until they are paired. Do this after the camera is
turned on and its status light is white.

If you do not have access to the administrative web interface:

1. Press and hold the IP button on the connector panel until the status light blinks cyan.

2. While the status light blinks cyan, press the pairing button on the remote. The camera's status light

changes to steady white when the pairing is complete. You may need to press the remote's pairing
button more than once.

3. If the status light changes from blinking cyan to blinking blue, this indicates a pairing error: The pairing

was not successful and pairing mode has timed out. Go back to step 1. If the problem persists,
contact Vaddio Technical Support.

Note

Any time a pairing error occurs (status light blinking blue), Vaddio recommends rebooting the camera as
soon as feasible. If pairing was successful, the remote remains paired through the reboot process.

If you have access to the administrative web interface:

1. On the Pairing page of the web interface, select Pair Remote.

2. When the camera's status light blinks cyan, press and hold the pairing button on the remote until the

status light changes to steady white.

Complete Manual for the IntelliSHOT Auto-Tracking Camera

35

Summary of Contents for 999-21100-009























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands