manualshive.com logo in svg

vacuubrand VACUU-PURE 10C, Instructions For Use Manual

Share
Download
vacuubrand VACUU-PURE 10C Instructions For Use Manual Download Page 69

69

20901224_EN_VACUU·PURE 10C_V1.8_221122

Cleaning and maintenance

7  

7   Cleaning and maintenance

Cleaning and maintenance

WARNING

Danger due to electrical voltage.

 

>

Switch the product off before cleaning or 

maintenance work.

 

>

Unplug the power plug from the socket.

Risk from contaminated parts.

Pumping hazardous media can result in hazardous 

substances adhering to internal parts of the pump.

 

>

Wear your personal protective equipment, e.g., 

protective gloves, eye protection and, if necessary, 

respiratory protection.

 

>

Take safety precautions according to your 

instructions for handling hazardous substances.

NOTE

NOTE

Damage possible if work is performed incorrectly.

 

>

Have maintenance work performed by a trained specialist or 

at least by a trained person.

 

>

Recommendation: Before carrying out maintenance work for 

the first time, please read through all the instructions to get 

an overview of the required service work.

Summary of Contents for VACUU-PURE 10C

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands