manualshive.com logo in svg

vacuubrand VACUU-PURE 10C, Instructions For Use Manual

Share
Download
vacuubrand VACUU-PURE 10C Instructions For Use Manual Download Page 62

62

20901224_EN_VACUU·PURE 10C_V1.8_221122

Error messages

6.3.2 

6.3.2  Error – Cause – Remedy

Error – Cause – Remedy

Error

Error

 

`

Possible cause

 

3

Remedy 

Personnel

Warning

 

flashing rate 

1x

 

`

Ambient temperature 

increased.

 

3

Observe the 

vacuum pump's 

limitation of use.

 

3

Ensure a supply of 

cooling air.

Specialist

 

`

Minimum clearances 

not observed when 

installed in lab 

furniture.

 

3

Maintain minimum 

clearances to 

adjacent objects or 

surfaces.

 

`

Cooling air supply 

blocked; fan grilles 

dirty.

 

3

Ensure a supply of 

cooling air.

 

3

Clean the fan 

grilles.

 

`

Cooling air outlet 

blocked.

 

3

Check and clear the 

cooling air outlet. 

Ensure cooling air 

outlet is kept clear.

 

`

Power supply too low, 

undervoltage.

 

3

Check mains 

voltage.

 

`

Pumping down hot 

process gases.

 

3

Observe admissible 

gas intake 

temperatures.

Warning

 

flashing rate 

3x

 

`

Motor current 

consumption in 

critical range, 

deposits in pump 

unit due to pumped 

media.

 

3

Clean the pump unit 

by rinsing it with 

water; 

see chapter: 

see chapter: 

7.3 Rinse vacuum 

7.3 Rinse vacuum 

pump on page 

pump on page 

73, 

73, 

and then 

dry in regeneration 

mode for at least 

60 minutes.

Operator

 

`

Motor current 

consumption in 

critical range during 

vacuum pump's rinse 

function.

 

3

Reduce the amount 

of 

rinsing water.

Warning

 

flashing rate 

4x

 

`

Fan speed deviation.

 

3

Remove possible 

blockage in the 

cooling air outlet.

Operator

Error – Cause – 

Remedy

Summary of Contents for VACUU-PURE 10C

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands