vacuubrand VACUU-PURE 10C Instructions For Use Manual Download Page 60

Page: 60 / 96

20901224_EN_VACUU·PURE 10C_V1.8_221122

Error messages

6.2

6.2 Error indication

Error indication

Flashing

Description

Temperature in the inadmissible range

not assigned

Motor current consumption in faulty range or

other motor error

Fan defective

Overvoltage or undervoltage in the intermediate

circuit of the frequency converter

Error / communication interruption VACUU·BUS

accessories

Other errors (software versions control board

/ frequency converter incompatible with each

other, other frequency converter errors)

If warnings and errors occur simultaneously, only the errors

(red LED) are displayed.

Several errors are indicated one after the other by combined

flashing cycles.

An error message is displayed until it is acknowledged.

Acknowledge an error message by switching the power

switch off and on after you have eliminated the error.

Example

Error

LED flashing rate

Temperature errors (1x)

and other errors (7x) occur

at the same time

Which and how many errors are present can be identified from

the flashing cycles.



Example

Pending error

Possible flashing

rates in the event of

an error

Summary of Contents for VACUU-PURE 10C

































































































Search results

Summary of Contents for VACUU-PURE 10C

Reviews:

Brands by name

Popular brands

vacuubrand VACUU-PURE 10C, Instructions For Use Manual

Search results

Summary of Contents for VACUU-PURE 10C

Reviews:

Brands by name

Popular brands